Güncel Gönderiler: Metalurji ve Malzeme Mühendisliği
Toplam kayıt 158, listelenen: 121-140
-
Properties and Corrosion Resistance of AISI H13 Hot-Work Tool Steel with Borided B4C Powders
(Korean Institute of Metals and Materials, 2019)Abstract: In this study, the surface of AISI H13 steel was borided with powder blends of B4C and NaBF4 using the powder-pack method at 800, 900 and 1000 °C for 2, 4 and 6 h. The structural and mechanical characteristics ... -
Production of new electromagnetic wave shielder mortar using waste mill scales
(Elsevier, 2020)Electromagnetic (EM) wave shielder mortar can be produced by mixing cement, natural limestone, tap water with mill scale (mill scale-I and mill scale-II) which is one of the biggest disposal area problems of the iron-steel ... -
St 22 Çeliğinin Derin Çekilebilirliğine Etki Eden Parametrelerin ANOVA ile Analizi
(2018)Bu çalışmada soğuk haddelenmiş ve ardından galvanizlenmiş St 22 çeliğininkimyasal bileşimi, soğuk haddeleme öncesindeki sac kalınlığı ve mekaniközellikleri (akma ve çekme gerilmesi, % uzama) ile soğuk haddeleme ezmeoranının ... -
Proximal probe-like nano structuring in metal-assisted etching of silicon
(American Institute of Physics Inc., 2019)We use silicon having multiple crystalline orientation domains and high metal doping in metal assisted chemical etching (MACEtch) in HF/H2O2. In device-quality silicon, MACEtch produces high-aspect ratio anisotropic (1-D) ... -
Investigations on machinability of Al2O3 reinforced Al6061 metal matrix composites
(Süleyman Demirel Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2016)In this study, six different MMCs containing Al6061 matrix and Al2O3reinforcements with particle sizes of 32 µm and 66 µm and weight fraction of 10%, 15% and 20% were produced using the vortex method. Machinability ... -
Investigation on wear mechanisms of boronized AISI 4140 steel
(Scibulcom Ltd., 2017)In this study, AISI 4140 steel was subjected to box boronizing treatment at 1123 K, 1173 K and 1223 K for 2h, 4h, and 6h with commercially EKabor 2 powders. Friction and wear behaviour of the boronized and following worn ... -
High temperature wear behavior of the surface-modified externally cooled rolls
(Elsevier, 2018)Externally cooled rolls of a steel plant were coated using three different surface modification techniques, namely titanizing, boronizing and borotitanizing. The grown coatings were examined using optical microscopy, ... -
Experimental and theoretical study of ultraviolet-induced structural/optical instability in nano silicon-based luminescence
(American Institute of Physics Inc., 2018)Nano silicon is emerging as an active element for UV applications due to quantum confinement-induced widening of the Si bandgap, amenability to integration on Si, and less sensitivity to temperature. NanoSi-based UV ... -
Micro-abrasion wear behavior of thermal-spray-coated steel tooth drill bits
(Polish Academy of Sciences, 2016)Wear behavior of four kinds of thermally sprayed coatings on steel tooth drill bits have been investigated by micro-abrasion wear test. The fixed ball micro abrasion wear test was applied for bare substrate and for thermal ... -
Structure Effect on K Shell Fluorescence Parameters at Bis-4-Bromobenzyl-1,2,4-Triazol-3-Ones
(Office Spectroscopy and Spectral Analysis, 2016)In this study; the effect of the electron density over the Br atoms raising with increasing number of CH2 group using the results of the K X-ray cross-sections and average fluorescence yields of bromine in quaternary-imidazole ... -
A Comparative Study on the Effects of Different Thermochemical Coating Techniques on Corrosion Resistance of STKM-13A Steel
(Springer, 2018)The corrosion resistances of three different thermochemical coatings (grown using titanizing, boriding, and borotitanizing treatments) applied to STKM-13A steel surfaces were investigated. The coatings were characterized ... -
Dry sliding wear behavior of bonded hot-work tool steel at elevated temperatures
(Elsevier Science, 2017)In the present study, the surface of AISI H13 hot-work tool steel was bonded with EKabor II powders using powder pack-bonding method. The process was carried out at 800,900 and 1000 degrees C temperatures for 2,4 and 6 h ... -
Wideband luminescence from bandgap-matched Mg-based Si core-shell geometry nanocomposite
(American Institute of Physics Inc., 2018)We use wet treatment to integrate red-luminescent Si nanoparticles with Mg-based wide-bandgap insulators Mg(OH) and MgO (5.7 and 7.3 eV respectively). In the process, Mg2+ is reduced on Si nanoparticle clusters, while ... -
The cooling rate effect on structure and flux pinning force of FeTeSe single crystal deposited by self-flux method
(Springer, 2018)Synthesis and characterization of FeTe0.5Se0.5 single crystals prepared by self-flux technique with two different cooling rates of 1.45 and 5.83 a"integral/h have been investigated. The XRD results show that the samples ... -
Exergy and performance analysis of a CI engine fuelled with HCNG gaseous fuel enriched biodiesel
(Inderscience Enterprises Ltd., 2017)Soybean oil based fatty acid methyl ester (FAME) is produced and blended with diesel fuel at 25% volumetric ratio. Besides, pure hydrogen (H2) and compressed natural gas (CNG) mixture named HCNG fuel is used with 20 litres ... -
Aromatic thermosetting copolyester foam core and aluminum foam face three-layer sandwich composite for impact energy absorption
(Elsevier, 2017)In this work, we introduce a three-layer sandwich composite structure having an aromatic thermosetting copolyester (ATSP) foam core with two aluminum foam face layers joined together by an in situ generated foaming mechanism. ... -
Properties and Tribologic Behavior of Titanium Carbide Coatings on AISI D2 Steel Deposited by Thermoreactive Diffusion
(Springer, 2018)In the present study, the metallographic, mechanical and tribologic behaviors of AISI D2 steel specimens coated with TiC through the titanizing process were investigated. The titanizing treatment was performed at the ... -
Microstructure and mechanical properties of borided inconel 625 superalloy
(Universidade Federal do Rio de Janeiro, 2017)The Ni-based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, ... -
Numerical thickness optimization study of CIGS based solar cells with wxAMPS
(Elsevier GmbH, 2016)In this paper, a numerical investigation of the effects of thickness of absorber and buffer layers for a typical CIGS based solar cell was carried out for the first time, employing the wxAMPS software which is a new ... -
Microabrasion Wear Behavior of Fast-Borided Steel Tooth Drill Bits
(Taylor and Francis Inc., 2017)In this study, the surface of steel tooth drill bits (Ni-Cr-Mo based) was subjected to the solid-state boriding treatment with 10- to 50-nm nanoboron powder. Boriding processes were carried out at a constant temperature ...
