Güncel Gönderiler: Makale Koleksiyonu
Toplam kayıt 126, listelenen: 101-120
-
Experimental and theoretical study of ultraviolet-induced structural/optical instability in nano silicon-based luminescence
(American Institute of Physics Inc., 2018)Nano silicon is emerging as an active element for UV applications due to quantum confinement-induced widening of the Si bandgap, amenability to integration on Si, and less sensitivity to temperature. NanoSi-based UV ... -
Structure Effect on K Shell Fluorescence Parameters at Bis-4-Bromobenzyl-1,2,4-Triazol-3-Ones
(Office Spectroscopy and Spectral Analysis, 2016)In this study; the effect of the electron density over the Br atoms raising with increasing number of CH2 group using the results of the K X-ray cross-sections and average fluorescence yields of bromine in quaternary-imidazole ... -
A Comparative Study on the Effects of Different Thermochemical Coating Techniques on Corrosion Resistance of STKM-13A Steel
(Springer, 2018)The corrosion resistances of three different thermochemical coatings (grown using titanizing, boriding, and borotitanizing treatments) applied to STKM-13A steel surfaces were investigated. The coatings were characterized ... -
Dry sliding wear behavior of bonded hot-work tool steel at elevated temperatures
(Elsevier Science, 2017)In the present study, the surface of AISI H13 hot-work tool steel was bonded with EKabor II powders using powder pack-bonding method. The process was carried out at 800,900 and 1000 degrees C temperatures for 2,4 and 6 h ... -
Wideband luminescence from bandgap-matched Mg-based Si core-shell geometry nanocomposite
(American Institute of Physics Inc., 2018)We use wet treatment to integrate red-luminescent Si nanoparticles with Mg-based wide-bandgap insulators Mg(OH) and MgO (5.7 and 7.3 eV respectively). In the process, Mg2+ is reduced on Si nanoparticle clusters, while ... -
The cooling rate effect on structure and flux pinning force of FeTeSe single crystal deposited by self-flux method
(Springer, 2018)Synthesis and characterization of FeTe0.5Se0.5 single crystals prepared by self-flux technique with two different cooling rates of 1.45 and 5.83 a"integral/h have been investigated. The XRD results show that the samples ... -
Exergy and performance analysis of a CI engine fuelled with HCNG gaseous fuel enriched biodiesel
(Inderscience Enterprises Ltd., 2017)Soybean oil based fatty acid methyl ester (FAME) is produced and blended with diesel fuel at 25% volumetric ratio. Besides, pure hydrogen (H2) and compressed natural gas (CNG) mixture named HCNG fuel is used with 20 litres ... -
Aromatic thermosetting copolyester foam core and aluminum foam face three-layer sandwich composite for impact energy absorption
(Elsevier, 2017)In this work, we introduce a three-layer sandwich composite structure having an aromatic thermosetting copolyester (ATSP) foam core with two aluminum foam face layers joined together by an in situ generated foaming mechanism. ... -
Properties and Tribologic Behavior of Titanium Carbide Coatings on AISI D2 Steel Deposited by Thermoreactive Diffusion
(Springer, 2018)In the present study, the metallographic, mechanical and tribologic behaviors of AISI D2 steel specimens coated with TiC through the titanizing process were investigated. The titanizing treatment was performed at the ... -
Microstructure and mechanical properties of borided inconel 625 superalloy
(Universidade Federal do Rio de Janeiro, 2017)The Ni-based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, ... -
Numerical thickness optimization study of CIGS based solar cells with wxAMPS
(Elsevier GmbH, 2016)In this paper, a numerical investigation of the effects of thickness of absorber and buffer layers for a typical CIGS based solar cell was carried out for the first time, employing the wxAMPS software which is a new ... -
Microabrasion Wear Behavior of Fast-Borided Steel Tooth Drill Bits
(Taylor and Francis Inc., 2017)In this study, the surface of steel tooth drill bits (Ni-Cr-Mo based) was subjected to the solid-state boriding treatment with 10- to 50-nm nanoboron powder. Boriding processes were carried out at a constant temperature ... -
Boride Layer Growth Kinetics Of Aisi H13 Steel Borided With Nano-Sized Powders
(Polish Academy Sciences, Institute Metallurgy & Materials Sciences, 2018)Growth kinetics of boride layers in AISI H13 steel was investigated using the pack bonding method at temperatures of 1073, 1173 and 1273 K (800 degrees C, 900 degrees C and 1000 degrees C) for periods of 2, 4 and 6 h with ... -
Properties and tribological performance of ceramic-base chromium and vanadium carbide composite coatings
(Elsevier, 2019)In the current study, the surface of AISI D2 steel was coated with the powder blends of ferro-vanadium (Fe-V) and ferro-chromium (Fe-Cr). The coatings were performed using a thermo-reactive diffusion (TRD) treatment by the ... -
Microstructural and mechanical properties of friction stir welded pure lead
(National Institute of Science Communication and Information Resources (NISCAIR), 2018)The present study focuses on the applicability of friction stir welding to pure Pb plates. The joint performances are evaluated by optical microscopy, microhardness measurements, notch impact tests and three point bending ... -
Performance of two low-cost GPS receivers for ground speed measurement under varying speed conditions
(Springer, 2017)A global positioning system (GPS) receiver is an important sensor used in modern farming, particularly in precision agriculture to determine geographic location and ground speed. The aim of this study was to investigate ... -
The investigation of K-shell fluorescence parameters of Zn-Fe alloys with different grain size and microstrain values
(Wiley, 2017)It is known that zinc alloys with iron group metals have better corrosion resistance than pure zinc. Owing to the corrosion resistance of these alloys, Zn-Fe coatings are widely used in automotive industry and have excellent ... -
Effect of borotitanizing on microstructure and wear behavior of Inconel 625
(Elsevier, 2017)Inconel 625, a nickel-based superalloy, is used in a wide range of applications including the marine and petroleum industries under where it is subjected to harsh conditions such as high temperatures and highly corrosive ... -
Farklı bor kimyasalları ile borlanmış Inconel 625 alaşımının karakterizasyonu
(Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, 2017)Bu çalışmada, nikel bazlı süper alaşımlar içerisinde endüstride yaygın olarak kullanılan Inconel 625 alaşımı 3 farklı borlama tozu ile borlanmıştır. Kullanılan borlama tozları, %90 elementel nano bor tozu + %10 NaBF4 (NB), ... -
Effect of long processing time on microstructure and transport properties of Fe1.1Se alloy produced by chemical vapor transport (CVT) technique
(Springer, 2018)In this work we present physical, electrical and magnetic properties of beta-Fe1.1Se single crystalline alloys produced by chemical vapor transport technique using short (120 h) and long (700 h) heating processes. The best ...
